Region Management Information
Region Management Information:
This DVD Player is designed and
manufactured to respond to the Region
Management Information that is recorded
on a DVD disc. If the Region number
described on the DVD disc does not
correspond to the Region number of this
DVD Player, this DVD Player cannot play
this disc.
CAUTION:
THIS DVD PLAYER IS A CLASS I
LASER PRODUCT. HOWEVER THIS
DVD PLAYER USES A
VISIBLE/INVISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE
DVD PLAYER CORRECTLY AS
INSTRUCTED.
USE OF CONTROLS OR
ADJUSTMENTSORPERFORMANCEOF
PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERSAND - DO NOT
REPAIRYOURSELF. REFERSERVICING
TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOTEXPOSE
THIS EQUIPMENT TO RAIN OR
MOISTURE.
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK,ANDANNOYING
INTERFERENCE, USE ONLY THE
RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR
CONTINUOUS OPERATION.
This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this
copyright protection technology must be
authorized by Macrovision Corporation,
and is intended for home and other
limited viewing uses only unless
otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
3
Disc formats supported by this player
DVD
Note these scratches are not an
indication of any problem with the player.
VID EO
12 cm disc
(Single-sided disc only)
Video CD
12 cm disc
CD
12 cm disc
MP3
12 cm disc
Discs which cannot be played with this
player
DVD-ROM
DVD-R/DVD-RAM
CDV
CD-G
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Preparing New Discs with Rough Spots
A new disc may have rough edges on its
inside and outside edges. If a disc with
rough edges is used, the proper setting
will not be performed and the player will
not play the disc. Therefore, remove the
rough edges in advance by using a ball
point pen or pencil as shown on the right.
To remove the rough edges, press the
side of the pen or pencil against the
inside and outside edges of the disc.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Note:
Adisc may become somewhat scratched
(although not enough to make it
unusable) depending on your handle it
and conditions in the usage environment.
4
Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure it is
all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
'
Install the unit where it does not get in the driver s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
Avoid installing the unit where it would be subject to high temperature, such as from
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,
dirt or excessive vibration.
This unit can be properly installed either from "Front"(conventional DIN Front-mount)
or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of
the unit chassis). For details, refer to the following illustrated installation methods.
30
5
HOW TO REMOVE AND INSTALL THE FRONT PANEL
1.Press the release button and pull-off the front panel.
Keep front panel into the case.
2.To install the front panel, insert the panel into the housing and make sure the panel
is properly installed, otherwise, abnormalities occurs on the display or some keys will
not function properly.
REMOVING THE FRONT PANEL
FRONT PANEL
RELEASE BUTTON
INSTALLING THE FRONT PANEL
7
WIRING CONNECTION
FOR 4x7W SYSTEM
MAIN UNIT
AUX(optional)
VIDEO IN YELLOW
RCH IN RED
ANTENNA CONNECTOR
LCH IN WHITE
RCA CABLE
GREY SUB WOOFER
VIDEO OUT 2 YELLOW
RED
IGNITION
SWITCH (B+)
0.5A
COAXIAL OUT BROWN
RCH RED
REAR RCA OUTPUT CABLE (OPTIONAL)
FRONT RCA OUTPUT CABLE
FUSE BOX
MEMORY(B+)
BACK-UP
LCH WHITE
YELLOW
BLACK
FRONT RCA
VIDEO OUT 1 YELLOW
FRONT RCA WHITE
R
RED
5A
GROUND (B-)
L
POWER
BLUE
(FOR RCA LINE OUT VERSION ONLY)
ANTENNA
WHITE
GREY
FRONT
FRONT
Lch SPK.
Rch SPK
WHITE/BLACK
GREY/BLACK
GREEN
VIOLET
REAR
REAR
Lch SPK.
Rch SPK
VIOLET/BLACK
GREEN/BLACK
8
11
13
1
12
14
MENU
DISPLAY
EJECT
GOTO
2
STOP
PLAY/PAUSE
ANGLE
MUTE
3
5
7
SUBTITLE
ZOOM
AUDIO
SLOW
4
6
8
15
17
19
TITLE
PBC
REPEAT
A-B
16
18
F.FWD
NEXT
ENTER
20
21
F.BWD
PREV.
9
1
2
6
9
3
4
5
7
8
SETUP
+10
0
10
22
Disc search button, cooperatively used with numeric buttons
Display statistical disc information during playback
Press it to eject the disc.(EJECT is enabled in DISC MODE only)
Changing of the SUBTITLE language on multi-subtitle
language DVD disc
1. GOTO
2. DISPLAY
3. EJECT
4. SUBTITLE
Changing of the AUDIO soundtrack on multi-audio soundtrack
DVD disc. Changing of the sound mode of the VCD/CD disc
Press it to zoom the picture in scale x1.5,x2.0,x3.0
Display the TITLE menu that is stored in DVD disc changing
between PBC ON and PBC OFF on the VCD disc
5. AUDIO
6. ZOOM
7. TITLE
Press
to start forward rapidly &
to reverse rapidly
8.
9.
/
Cursor buttons in MENU mode.
Display the SETUP menu
Press it to stop playback
/
/
/
10.SETUP
11
Press once to pause a play, press again to resume playback.
Press MENU to display the root menu of the DVD disc.
Press it to elimate the sound immediate
Changing for slow forward/reverse playback motion
Changing of the view angle on multi-angle DVD disc
Press it to repeat between two selected sports on DVD orVCD disc
Switch the Repeat mode of DVD/VCD/CD disc
12.
13. MENU
14. MUTE
15.SLOW
16.ANGLE
17.A-B
18.REPEAT
Press
to skip to the next track & press
to skip back one track
19.
/
Confirm the Track/Chapter selected with the number key or
selected with the cursor buttons on TV screen
Numeric buttons
20.ENTER
21. 0 - 9
22. +10
Press it to select 10th digits
9
Preparing the Remote Control
Inserting the Batteries
1.Open the battery compartment cover.
2.Insert the new batteries. Make sure that the positive and negative terminals of the
batteries are oriented indicated.
3.Close the cover
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each the direction of the front of the IR mark.
10
18
17
16
15
11
10
2
3
4
5
6
7
8
9
12 13 14
1
20
19
ON/OFF
Press POWER button (13) to turn on the unit. Press it again to turn off.
FACEPLATE RELEASE
Press REL button (2) to detach the removable faceplate.
SET THE CLOCK
Press CLK button (6) to change the display to clock display. Press it again to return
to previous display. In clock display, press and hold theCLK button (6) for several
seconds until the clock display flashes. Press VOL - (9) to change minutes or
VOL+ (10) to change hours.
SELECT MODE
Press SEL button (8) to change audio mode through volume, bass, treble, balance,
and fader modes. Use VOL + (10) and VOL- ( 9) buttons to adjust the selected mode
When mode has not been adjusted for several seconds, display returns to normal
radio or CD display.
VOL
(Volume)
BAS
(Bass)
TRE
(Treble)
BAL
(Balance)
FAD
(Fader)
11
Volume
Adjust volume level by using VOL+ (10) and VOL- (9) buttons.
Note: The unit is initially set to volume mode.
Bass
Press SEL button (8) one time. Adjust bass level by using VOL+(10) and VOL-(9)
buttons.
Treble
Press SEL button (8) two times. Adjust treble level by using VOL+(10) and VOL
-(9) buttons.
Balance
Press SEL button (8) three times. Adjust sound balance between left and right
speakers by using VOL+(10) and VOL-(9) buttons.
Fader
Press SEL button (8) four times. Adjust sound balance between front and rear
speakers by using VOL+(10) and VOL-(9) buttons.
MUTE
Press MU button (4) to mute down sound. Press it again to release this mode and
recover previous volume level.
SELECT MODE
Press MOD button (12) to change between radio or disc mode.
EQUALIZATION
Press EQ button (7) to turn to equalization function and to select desired audio
mode.
There are four kinds of mode as below:
FLAT
CLAS
ROCK
POP
NO EQ
LIQUID CRYSTAL DISPLAY
The LCD can show the current state of the unit
SKIP TRACKS
Press
button(16) or
button(15)to the previous track or the following track .
Track number shows on the display.
12
FLASHING LED
If the front panel is not on the main unit, LED (19) will be flashing.
RESET BUTTON FUNCTION
RESET button (20) is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for the
following reasons:
-Initial installation of the unit when all wiring is completed.
-All the function buttons do not operate.
-Error symbol on the display.
Note: If press RESET button , the unit can't work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
RADIO OPERATION
BAND
Press BND button (11) to change bands as below:
FM MW LW
FM
MW
FM
AM
For 3 Bands (Europe)
For 2 Bands (Europe)
For 2 Bands (USA)
SELECT STATION
Rotate TUNING knob (3) clockwise or anticlockwise to adjust the frequency upward
or downward.
AF
AF button (1)[ALTERNATIVE FREQUENCIES](FOR RDS ONLY)
1. By pushing short.
1) RADIO mode
changed the mode to CDP mode.
2). CDP mode
changed the PLAY mode to PAUSE mode and vice versa.
2. By pushing long.
It is engaging whether "AF SEARCH" mode ON or OFF.
If "AF SEARCH" mode is tunred on, the 1'st AF is displayed onthe LCD. All the
AF list can be shown by pressing "DISPLAY" key during "AF SEARCH ON" mode.
When AF is shown, the display mode changes to the frequency if the user
changes the frequency.RDS signal is NOT received during AF search mode.
This mode is released after few seconds. But, this mode is NOTreleased during
changing the tunned frequency to search AF.
LOCAL/DISTAN
Press the LOC button (18) to select between local setting for reception of strong
station and distant setting for reception of weak stations when tuning.
MONO/STEREO
In FM band, press MON button (5) to select mono or stereo reception for radio
stations. You can sometimes improve reception of distant stations by selecting
mono operation.
TA
TA function [TRAFFIC ANNOUNCEMENT] BUTTON(FOR RDS ONLY)
When pressed short
1). RADIO mode
Depending on the installed option diode matrix,
LW/MW/FM band is toggled cyclically through the tuning bands.
-> FM -> MW -> LW (for 3 bands Europe)
or
13
BASIC OPERATION
-> FM -> MW -> (for 2 bands Europe)
-> FM -> AM -> (for 2 bands USA)
Refer to the explanation of diode matrix.
2). CDP mode
or
or
changed the mode to Radio mode.
When pressed long, it is engaging whether TA mode on or off.
When TA mode is on and a traffic announcement is transmitted:
TA(INFO) - When the unit was in CDP mode, it will switch temporarily to radio
mode.
- If the volume level was under the threshold point it will be raised to the
threshold point.
But the user changed the volume level which was more than the threshold point
(min .TA volume level), it will be set to the last level.
When TA mode is on,TA of individual segment is turned on.
- When a TP station is received,TP of individual segment is turned on.
The current traffic announcement is canceled by pressing this key.But the TA
mode will not be off.
DISC OPERATION
Most of the disc operations are controlled by the remote controller.
Ejecting a Disc
Press (EJECT) button (17) on the front panel or ON the remote control to eject the disc.
Stopping Play
-Brief press the (Stop) button to stop the unit playback, when press the
button it can continuous normal playback.
(14)
-Press (Stop) button twice, it will stop the playback and go back to initial Track/Chapter.
Rapid Forward/Rapid Reverse
Press
F.FWD&
F.BWD during play.
Each time the button is pressed, the speed of rapid forward/reverse changes according
to the disc as follow.
DVD:
VCD/CD:
Mp3:
Normal Playback 2x
4x
6x
8x
Normal Playback
2x
3x
4x
Normal Playback
2X
4X
Skipping Track
Press
skip to next track or back one track.
/
on the remote handset or
/
on the front panel during playback to
and buttons may be un
Note: For some VCD 2.0 dics(PBC-playback control),
available.
Slow Motion Play
Press slow button during playback.Each time the button is pressed, the slow modes are
changes according to the disc as follow.
DVD:
Normal Playback
VCD:
Normal Playback
SF 1x
SF 2x
SF 3X
SF 2x
SF 4x
SF 8x
SR 8X
SR 4X
SR 2X
Step BWD
Note: For VCD, in any slow mode, press ENTER button to return to normal playback.
14
Pause (still picture)
On-Screen Display Function
Press the DISPLAY button during
playback to display the contents of the
current disc on the screen.
Example:
Pressing
during playback will stop
play temporary. Return to normal
playback, press
once again.
Repeat
DVD:
Press the REPEAT button to select repeat
mode as follow.
(1) Press DISPLAY for the first time:
DVD:
TITLE 01/03 CHAPTER 002/025 P: 00:00:25
TITLE ELAPSED
Press the REPEAT button to select repeat
mode as follow.
CHAPTER REPEAT ON
TITLE REPEAT ON
REPEAT OFF
Title Number, Total Title Number, Chapter
Number, Total Chapter Number of this
Title of the disc currently being played
will be shown on the screen, along with
the elapsed time.
VCD/CD:
Press the REPEAT button to select repeat
mode as follow.
REP-ONE
REP-ALL
REPEAT OFF
(2) Press DISPLAY for the second time:
TITLE 01/03 CHAPTER 002/025 P: 00:00:25
TITLE REMAIN
1.Continuously repeat at the current chapter/
track, when selected REP-ONE mode.
2.Select REP-ALL mode to continuously
repeat all chapter/track on the current
disc.
(3) Press DISPLAY for the third time:
3.When the player finish playback the
current discc last chapter/track, it will
stop display the elapsed time.
When selected REPEAT OFF mode
(REP-ONE & REP-ALL disappear at
the screen display).
TITLE 01/03 CHAPTER 002/025 P: 00:00:25
CHAPTER ELAPSED
(4) Press DISPLAY for the fourth time:
4.REPEAT feature does not supportVCD2.0
(with PBC ON).
TITLE 01/03 CHAPTER 002/025 P: 00:00:25
CHAPTER REMAIN
Remote Sensor (IR)
Point the remote handset to the remote
sensor. Receive the signal from remote
handset.
(5) Press DISPLAY for the fifth time:
The message on thescreen willbecleared.
Video CD/SVCD/CD:
(1) Press DISPLAY for the first time:
T:01/18 P: 00:00:25 LR DISC
SINGLE ELAPSED
15
(2) Press DISPLAY for the second time:
VCD:
Press AUDIO during playback.
It is possible to switch the sound
between monaural and stereo sound.
T:01/18 P: 00:00:25 LR DISC
SINGLE REMAIN
LEFT VOCAL
RIGHT VOCAL
MONO LEFT
(3) Press DISPLAY for the third time:
STEREO MONO RIGHT
T:01/18 P: 00:00:25 LR DISC
TOTAL ELAPSED
CD:
Press AUDIO during playback.
It is possible to switch the sound
between monaural and stereo sound.
(4) Press DISPLAY for the fourth time:
MONO LEFT
MONO RIGHT
STEREO
T:01/18 P: 00:00:25 LR DISC
TOTAL REMAIN
TITLE Menu Function
DVD:
(5) Press DISPLAY for the fifth time:
The message on the screen will be cleared
for SVCD and VCD. Note: For CD and
Mp3, the message will always display
on the screen.
If the DVD has multiple titles recorded on
the disc. It can select preferred title from
the title menu to start playback.
1.Press TITLE during playback.
The title menu is display.
2.Press the cursor button shown in TV
screen, select preferred title by the
cursor button and confirmed by
ENTER key.
MP3:
Each time DISPLAY is pressed, the
message displayed on screen changes
as follows:
VCD:
Press MENU button while the disc is
playing, you can switch between"PBC
on"and "PBC off"mode.
SINGLE ELAPSED
SIGGLE REMAIN
Multi-audio Language Function
DVD:
Multi-subtitle Language Function
(For DVD only)
Press AUDIO during playback.
Each time the button is pressed, number
of the audio soundtrack language
changes on sequential order.
Notes:
-The language number is different
according to the disc.
-Some disc only contain one language
soundtrack.
Press SUBTITLE during playback.
Each time the button is pressed, number
of the subtitle language changes in
sequential order.
Notes:
-The language number is different
according to the disc.
-Some discs only contain one
subtitle language.
-When no different subtitle language
are recorded, will be displayed at
screen left top corner.
-When no different language
soundtrack are recorded will be
display at screen left top corner.
16
Multi-angle Function
(For DVD only)
Press ANGLE during playback.
MP3 Disc Play
MP3 disc is playing as the format of
FOLDER by FOLDER.
Each time the button is pressed, number For example:
of the angle changes in sequential order.
Notes:
Mp3 PLAYER
ROOT
-The angle number is different according
ROOT
0
1
to the disc.
-The function only work for discs having
scenes recorded at different angles.
-When no different angle are recorded,
will be displayed at screen left top
corner.
MP3 MUSIC
SKY
MP3 HEAR YOUR
Use
/
/
/
to select the item or
folder, then press ENTER button.
Pressing REPEAT button repeatedly can
select three kinds of repeat play mode.
REP-ONE:
Play the same song over and over again.
FOLDER REPEAT:
Play all songs in the current directory in
sequence, over and over again.
DISC REPEAT:
Play all songs in the disc over and
over again.
In the playback, use
item ahead or back.
: Rapid reverse,
or
to skip an
: Rapid advance
Note: The FOLDER cannot be selected
during playing. It can be selected after
(Stop) button pressed.
17
INITIAL SETUP
SETUP MENU --- MAIN PAGE---
GENERAL SETUP
--- GENERAL PAGE ---
GENERAL SETUP
SPEAKER SEUP
AUDIO SETUP
NORMAL/PS
NORMAL/LB
TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
WIDE
PREFERENCES
EXIT SETUP
1.Press SETUP in the stop mode.
(Press the stop button twice to ensure
the player under STOP mode.)
MAIN PAGE
TV Screen
2.The initial SETUP menu is displayed.
3.Select the preferred item by using the
Video
Material
Wide(16:9)
Pan Scan
Normal
Letter-box
4:3
/
buttons.
4.Press ENTER buttons.
a. GENERAL SETUP
This setup page includes all the
item of TV display & audio output
TV display setup
This is to select the appropriate TV
feature. The detail please refer to aspect (4:3 or 16:9) according to the
GENERAL SETUP MENU.
b. SPEAKER SETUP
connected TV set.
Normal/PS (For 4:3 TV)
This is to activate the audio output
from DOLBY AC3 5.1 DOWNMIX
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the left
to 2 channel mode. Please refer to and right edges are cut off.)
SPEAKER SETUP MENU.
c. AUDIO SETUP
Normal/LB (For 4:3 TV)
Played back in letterbox style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
This setup page includes all the
items for AUDIO. Please refer to
AUDIO SETUP MENU.
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
d. PREFERENCE SETUP
This setup page includes all the
configuration of support feature.
The detail please refer to
PREFERENCES SETUP MENU.
18
--- GENERAL PAGE ---
TV DISPLAY
--- GENERAL PAGE ---
TV DISPLAY
PIC MODE
AUTO
HI-RES
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
N-FLICKER
ENGLISH
MAIN PAGE
MAIN PAGE
PIC mode setup
OSD LANG type setup
Select AUTO, the player PIC mode will
depend on DVD disc.
Select the preferred OSD language by
using the buttons.
/
Select HI-RES format for best image
resolution.
Select N-FLICKER format on format on
image or picture under noise affect.
--- GENERAL PAGE
TV DISPLAY
PIC MODE
--- GENERAL PAGE ---
TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
ON
CAPTIONS
SCR SAVER
ON
OFF
OFF
MAIN PAGE
MAIN PAGE
ANGLE MARK display setup
CAPTIONS setup
If it is set to ON, when the multi-angle
Activate the CAPTIONS feature by
DVD disc is playing, (the angle mark) selecting ON. And release this feature
will appears on the screen; if is set to
OFF, the mark will not appear.
by selecting OFF.
19
AUDIO SETUP
--- AUDIO SETUP ---
--- GENERAL PAGE ---
TV DISPLAY
AUDIO OUT
OP MODE
ANALOG
SPDIF/RAW
SPDIF/PCM
PIC MODE
LPCM OUTPUT
DYNAMIC
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
ON
OFF
MAIN PAGE
MAIN PAGE
AUDIO OUT
SCR SAVER setup
This is to activate the audio output from
ANALOG mode to SPDIF/RAW mode to
SPDIF/PCM mode.
Select the SCR SAVER output ON/OFF.
SPEAKER SETUP
--- AUDIO SETUP ---
--- SPEAKER SETUP PAGE ---
DOWNMIX
LT/RT
AUDIO OUT
OP MODE
LINE MODE
RF REMOD
STEREO
MAIN PAGE
LPCM OUTPUT
DYNAMIC
MAIN PAGE
OP MODE
This is to activate the audio output from
DOLBYAC3 5.1 DOWNMIX to 2 channel
mode. Select the preferred SPEAKER
connection by using the cursor buttons.
Select the LT/RT to activate the Dolby
surround compatible output.
There are two operating modes for the
Dolby Digital decoder: LINE OUT and
RF REMOD.
Select the STEREO to activate simple
stereo mode.
20
PREFERENCES SETUP
--- AUDIO SETUP---
AUDIO OUT
--- PREFERENCES PAGE ---
TV TYPE
MULTI
NTSC
PAL
AUDIO
OP MODE
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
LPCM OUTPUT
DYNAMIC
LPCM 48K
LPCM 96K
DEFAULTS
MP3 PLAY
MAIN PAGE
MAIN PAGE
TV type setup
LPCM OUTPUT
This player can play discs recorded in
either PAL or NTSC format.
Select NTSC format, when you connected
to NTSC TV.
Select PAL format, when you connected
to PAL TV.
Select AUTO format, the player TV
output format will according to the DVD
disc format.
Select the LPCM OUTPUT between
LPCM 48K and LPCM 96K.
--- AUDIO SETUP ---
AUDIO OUT
FULL
OP MODE
6/8
--- PREFERENCES PAGE ---
LPCM OUTPUT
TV TYPE
4/8
DYNAMIC
AUDIO
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
2/8
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
OFF
MAIN PAGE
DEFAULTS
MP3 PLAY
MAIN PAGE
Dynamic Range Control
Select DRC and adjust the dynamic
range of a Dobly Digital encoded
program. There are 8 steps between full
compression and off compression.
AUDIO language setup
Select the preferred AUDIO soundtrack
by using the cursor buttons.
21
--- PREFERENCES PAGE ---
TV TYPE
--- PREFERENCES PAGE ---
TV TYPE
1G
AUDIO
AUDIO
2
ENGLISH
FRENCH
SPANISH
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
3PG
4PG13
5
CHINESE
6PG-R
JAPANESE
OFF
DEFAULTS
MP3 PLAY
MAIN PAGE
DEFAULTS
MP3 PLAY
7NC-17
8 ADULT
MAIN PAGE
NO PARENTAL
PARENTAL
Select the preferred SUBTITLE language
by using the cursor buttons.
Select suitable parental guidance by the
cursor buttons and conformed by
pressing ENTER button.
--- PREFERENCES PAGE---
--- PREFERENCES PAGE ---
TV TYPE
AUDIO
TV TYPE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
ENGLISH
FRENCH
SPANISH
PASSWORD
CHANGE
DEFAULTS
MP3 PLAY
MAIN PAGE
DEFAULTS
MP3 PLAY
MAIN PAGE
CHINESE
JAPANESE
Select the preferred DISC MENU
Select the change and press ENTER
language by using the cursor buttons.
button. Type the old password (The initial
factory code is
) and key in 4
characters password now you want to
use, and retype again to confirm key in
correctly.
22
--- PREFERENCES PAGE ---
DEFAULTS TABLE
Normal/PS
General Setup
TV Display
PIC Mode
TV TYPE
AUDIO
AUTO
ON
Angle Mark
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
OSD Language
Captions
English
OFF
SCR Saver
OFF
Stereo
Analog
Speaker Setup Downmix
Audio Out
Audio Setup
RESET
DEFAULTS
MP3 PLAY
MAIN PAGE
OP Mode
Dynamic
Line Out
LPCM 96K
AUTO
LPCM Out
TV Type
Audio
Preferences
DEFAULTS
English
English
English
Select reset to become factory initial
Subtitle
setting.
DISC Menu
--- PREFERENCES PAGE ---
Parental
NO PARENTAL
Password
Smart NAV
3308
TV TYPE
With Menu
AUDIO
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
NO MENU
MP3 PLAY
WITH MENU
MAIN PAGE
Mp3 PLAY
In this item, you can select NO MENU
mode or WITH MENU mode.
23
Supply Voltage:
Current Consumption:
Signal System:
12V DC (11V-15V), test voltage 14.4V, negative ground
Less than7 A
Compositive video 1.0Vp-p 75
Discs Played:
(1)DVD-VIDEO Disc
5"(12 cm) single-sided, single-layer
5"(12 cm) single-sided, double-layer
(2)Compact Disc (CD-DA, VIDEO CD)
5"(12cm) disc
Audio Output Level:
Audio Signal Output:
Characteristics:
600 (2 ch 2.0 Vrms)
(1)Frequency Response
(2)S/N Ratio
20 Hz - 20 KHz
90 dB (JIS)
(3)Wow and Flutter
Below measurable limits
For 3 Bands
(Europe)
For 2 Bands
(Europe)
For 2 Bands
(U.S.A.)
FM
FM
FM
Frequency Coverage:
IF:
Sensitivity (S/N = 30 dB):
88 to 108 MHz 88 to 108 Mhz 88 to 108 MHz
10.7 MHz
15 dBu
10.7 MHz
15 dBu
10.7 MHz
15dBu
MW
MW
AM
Frequency Coverage:
IF:
Sensitivity (S/N = 20 dB):
540 to 1600 KHz 540 to 1600 KHz 530 to 1710 KHz
455 KHz
40 dBu
455 KHz
40 dBu
455 KHz
40 dBu
LW
Frequency Coverage:
IF:
Sensitivity (S/N = 20 dB):
150 to 280 KHz
455 KHz
45 dBu
Note:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
24
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
Cause
Solution
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
The car ignition switch is
not on.
No power.
The fuse is blown.
Replace the fuse.
Remove the disc in the player,
Then put a new one
Presence of disc inside the
player.
Inserting the disc in reverse
direction.
Insert the compact disc with
the label facing upward.
Disc cannot be
loaded or ejected.
The disc is extremely dirty or
defective.
Clean the disc or try to play a
new one.
Temperature inside the car
is too high.
Cool off or until the ambient
temperature return to normal.
Leave the player off for an hour
then try again.
Condensation.
Adjust volume to a desired level.
Check wiring connection.
Volume is in minimum.
No sound.
Wiring is not properly
connected.
Adjust the installation angle less
than 30 degrees.
The installation angle is
more than 30 degrees.
Sound skips.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
Press the RESET button.
Front panel is not properly fixed
into its place.
The built-in microcomputer
is not operating properly
due to noise.
The operation keys
do not work.
The antenna cable is not
connected.
Insert the antenna cable firmly.
Select a station manually.
The radio does not
work.
The signals are too weak.
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
25
88-V2420-03
|