INSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATION
Please read all instructions carefully
DMH100 SERIES
before beginning installation.
TOOLS REQUIRED
#1 Phillips screwdriver (small)
C A U T I O N
To avoid electrical shock
and to prevent damage to
the furnace, air conditioner,
and thermostat, disconnect
DIGITAL MECHANICAL THERMOSTAT
Drill with 3/16-in. (4.8mm) bit
F
OF
Easy as
1–2–3
PRO
THERMOSTAT LOCATION
On replacement installations, mount
the new thermostat in place of the
old one unless the conditions listed
below suggest otherwise.
On new installations, follow the guidelines listed below.
1. Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and in a
room that is used often.
the power supply before beginning
work. This can be done at the fuse
box, at the circuit breaker, or at
the appliance.
Complete, Easy To Read Programming And Installation Instructions Inside
LUX PRODUCTS CORPORATION • Mt. Laurel, New Jersey 08054, USA
44308-04
WARNING: Use Energizer® or DURACELL® Alkaline Batteries Only.
Energizer® is a registered trademark of Eveready Battery Company, Inc.
DURACELL® is a registered trademark of The Gillette Company, Inc.
2. Do not install it where there are unusual heating conditions, such as: in direct
sunlight; near a lamp, radio, television, radiator, register, or fireplace; near hot
water pipes in a wall; near a stove on the other side of a wall.
3. Do not locate in unusual cooling conditions, such as: on a wall separating an
unheated room; or in a draft from a stairwell, door, or window.
4. Do not locate in a damp area. This can lead to corrosion that will shorten
thermostat life.
5. Do not locate where air circulation is poor, such as: in a corner or an alcove; or
behind an open door.
6. Do not install the unit until all construction work and painting has been
completed.
I M P O R T A N T !
Thank you for your confidence in our product. To obtain the best
results from your investment, please read this manual and acquaint
yourself with your purchase before installing your new thermostat.
Then follow the installation procedures, one step at a time. This will
save you time and minimize the chance of damaging the thermostat
and the systems it controls.
7. This thermostat does not require leveling.
C A U T I O N
Read instructions carefully
These instructions may contain information beyond that required for your particular installation.
Please save for future reference.
REMOVING THE OLD THERMOSTAT
1. Remove cover from old
thermostat. Most are snap-
on types and simply pull off.
Some have locking screws
on the side. These must be
loosened.
Switch electricity to the
before removing any wiring
from existing thermostat.
Wires must be labeled
before they are removed.
When removing wires from
their terminals, ignore the
color of the wires since
these may not comply with
the standard.
W
FEATURES
• The unit can be used with most
24 volt gas, oil or electric heating and
air conditioning systems, gas millivolt
furnace and air conditioner OFF; then
proceed with the following steps.
heating systems, and single stage heat pumps.
It cannot be used with 120 volt heating systems
or two stage heat pumps. Ask your dealer for
other LUX thermostats to control those systems.
2. Note the letters printed near the terminals. Attach labels (enclosed) to each
wire for identification. Remove and label wires one at a time. Make sure the
wires do not fall back inside the wall.
3. Loosen all screws on the old thermostat and remove it from the wall.
• A large easy to read display shows you
the current room temperature at all times.
MOUNTING THE UNIT ON THE WALL
1. Press down on the button on top of thermostat and swing the body away
from the base and down to remove the body from the base.
• The unit has a built in digital control system
to accurately control the temperature in your home.
• The unit will learn the temperature characteristics of your home on a daily basis and
customize the control to give you the best comfort possible from a digital thermostat.
2. Strip insulation 3/8
in. (9.5mm) from wire
ends and clean off
any corrosion.
3. Fill wall opening with
non-combustible
insulation to prevent
drafts from affecting
the thermostat.
Y
• You can also select a tighter temperature control if you have a forced hot water system or if
closer comfort is preferred over energy savings.
R
•
A press of either the Temperature Up or Down key will reveal the current Set Temperature.
•
A 4-minute minimum off time in COOL prevents your air conditioning system from being
damaged.
Two Energizer® or DURACELL® “AA” alkaline batteries (not included) are used to retain
your time and temperature programs.
•
C
A
U
T
I
O
N
Be careful not to drop the body or disturb electronic parts.
C
A
U
T
I
O
N
• Your thermostat is a precision instrument. Please handle it with care.
• Turn off electricity to the appliance before installing or servicing thermostat or any part
of the system. Do not turn electricity back on until work is completed.
• Do not short (jumper) across electric terminals at control on furnace or air conditioner
to test the system. This will damage the thermostat and void your warranty.
• All wiring must conform to local codes and ordinances.
• This thermostat is designed for use with 24 volt and millivolt systems. The thermostat
should be limited to a maximum of 1.0 amps; higher amperage may cause damage to
the thermostat. If you are in doubt, call your utility company.
© COPYRIGHT 2004 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
1
•
•
•
In the winter, set the system switch to HEAT to control your heating system.
In the summer, set the switch to COOL to control your air conditioner.
These diagrams are provided for new installations or unreferenced wires.
In spring and fall or when windows are open, you can set the system switch
OFF.
•
•
Setting the FAN switch to AUTO automatically runs your system’s fan during
heating and cooling.
Setting the FAN switch to
N
O
T
E
ON runs your system’s fan
continuously even without
heating or cooling.
The FAN switch works only if your system
provides a wire for the UNIT’S “G” terminal.
ADVANCED FEATURES
TEMPERATURE SWING
A thermostat works by turning your heating or cooling system on and off whenever the room
temperature varies a certain number of degrees from the set-point temperature. This variation is
the “swing.”
Your thermostat is carefully tuned to provide you with exceptional comfort as well as provide you
with energy savings. Should you desire to have the temperature controlled even more tightly in
your home at the expense of increased energy savings, you can change the swing value. Also
users of forced hot water systems may find this setting more comfortable.
Located on the back of the thermostat body are three jumpers.
To change from 0.5 degree F control to 0.25 degree F control, remove the jumper indicated by
0.5 F / 0.25 F.
INSTALLING BATTERIES/ MAINTENANCE
Press the small unmarked button on the front of the thermostat with a paper clip for the change
to take effect. The unit will now control your home to 0.5 degrees.
The unit requires batteries to operate your furnace and retain its memory.
Replace the batteries when the LO BATT indicator appears in the display or at
least once a year.
5 MIN/2 MIN MINIMUM RUN TIME
Your thermostat has an internal timer built in to protect your compressor. The timer forces a
minimum on-time of 5 minutes. You may change this minimum on-time to 2 minutes. To
accomplish this, place the jumper labeled W3 over both pins. You must press the small
unmarked button on the face of the thermostat for the changes to take effect.
N O T E
If you have an electric system and the blower does not operate after installation, find the
electric/gas heat selector on the back of the body. Move the selector to the ELEC position.
Elec/Gas
C/F Jumper
Selector
1. Remove fresh batteries from
their carton.
CHANGING FROM °F TO °C
• To change to Celsius - place the jumper
labeled W2 over both pins.
ELECT
2. Remove body of thermostat as
described during installation.
3. Remove the used batteries.
GAS
Battery
4. Install two new Energizer® or
Compartment
• Press the small unmarked button on the
front of the thermostat for the changes
to take effect.
DURACELL® "AA" size alkaline
batteries in the battery compartment.
Observe the polarity marking
shown in the compartment.
W1
W3
0.5F - SHORT
0.25F - OPEN
0.28C - SHORT
0.14C - OPEN
W1 (SWING)
W2 (C/F)
Swing Jumper
F - OPEN
C - SHORT
REPLACE BATTERIES WHEN INDICATOR APPEARS
WARNING: Use Energizer® or
DURACELL®
N O T E
Alkaline Batteries Only.
When replacing batteries, you
have approximately 1 minute
before programs are lost.
TECHNICAL SERVICE
If you have any problems installing or using this thermostat, please reread the instructions carefully.
Technical Service is available through our Technical Service Number. If you require assistance, please
call our offices between 8:00 a.m. and 4:30 p.m. Eastern Standard Time, Monday through Friday.
5. Place the body back on the wall. Hook the bottom
of the body onto the base, swing the body up
and snap the body onto the base.
Installation is now complete. Be sure to turn the power back on to your heating
and/or air conditioning system. Within 90 seconds the thermostat will begin to
display the room temperature.
WARRANTY
6. Press either the TEMPERATURE UP or DOWN key in order to show the current
SET TEMPERATURE.
Limited Warranty: If this unit fails because of defects in materials or workmanship within one year of
date of original purchase, LUX will, at its option, repair or replace it. This warranty does not cover
damage by accident, misuse, or failure to follow installation instructions. Implied warranties are limited in
duration to one year from date of original purchase. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. Please return malfunctioning or
defective units to the participating retailer from which purchase was made, along with proof of purchase.
Please refer to Technical Service Section before returning thermostat.
Purchaser assumes all risks and liability for incidental and consequential damage resulting from
installation and use of this unit. Some states do not allow the exclusion of incidental or consequential
damages, so the above exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state. Applicable in the U.S.A. only.
7. Press TEMPERATURE UP or DOWN keys again until your desired temperature is
displayed. The display will show the current room temperature again after two
seconds.
N O T E
If you have an electric system and the blower does not operate after installation,
find the electric/gas heat jumper on the back of the body as indicated on the diagram
below. Move the jumper from the pins on the far right to the pins on the far left.
© COPYRIGHT 2004 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
3
|