Telestar RB-60.qxd 4/11/06 2:04 PM Page 1
TELESTAR INSTRUCTION MANUAL
60mm | 2.4" Altazimuth Refracting Telescope
RB-60
Telestar RB-60.qxd 4/11/06 2:04 PM Page 3
INTRODUCTION
Your telescope is an excellent beginner’s
instrument, and is designed to observe
objects in the sky and also on land. It can be
your personal window on the universe or
allows you to intimately study the behavior of
nesting birds on a distant hillside.
Setting up your telescope involves these
simple steps:
• Assemble your tripod
1
• Attach the accessory tray
• Attach the optical tube to the mount
• Attach the red dot viewfinder
• Attach the diagonal mirror and eyepiece
• Align the red dot viewfinder
The telescope is shipped with the following
parts:
• Optical tube
Study the the picture on the next page and
become acquainted with the parts of your
telescope. Then proceed to “Assemble
your Tripod.”
• Aluminum tripod with an accessory tray
• Two 1.25" eyepieces: MA25mm (28X),
MH9mm (78X)
• 2x 1.25" Barlow lens
• Diagonal mirror
• Red dot viewfinder with bracket
• Telescope mount
The tube has a focal length of 700mm, and
its objective lens has a diameter of 60mm.
The lens diameter is one of the most
important pieces of information about the
telescope. The size of the objective lens
determines how much detail you will be able
to see in your telescope. The focal length will
help later on to calculate magnification.
Telestar RB-60.qxd 4/11/06 2:04 PM Page 4
Inset A
Figure 1: Telestar RB-60 Altazimuth Refracting Telescope
FIGURE 1
Inset A:
Inset B:
Inset C:
Red Dot Viewfinder Assembly
Tripod Legs and Accessory Tray
Altaz or Altazimuth Mount
2
1. Eyepiece
2. Red dot viewfinder (see Inset A)
3. Red dot viewfinder alignment screws
(see Inset A)
4. Optical tube assembly
5. Vertical locking lever
6. Horizontal lock knob
Inset B
7. Tripod legs
8. Leg brace supports (See Inset C)
9. Leg brace (See Inset C)
10. Mount base attachment knobs
11. Optical tube lock knobs
12. Horizontal slow motion control (See Inset B)
13. Diagonal mirror
14. Objective lens cell
15. Focuser drawtube
16. Vertical slow motion control (See Inset B)
17. Accessory tray (Inset C)
18. Red dot viewfinder bracket (see Inset A)
19. Adjustable sliding leg extension (see Inset C)
20. Tripod leg lock (see Inset C)
21. Dew shield/lens shade
22. Front lens cap (removed)
23. Focusing knob
Inset C
24. Mount base attachment
25. Quickrelease (Inset A)
Telestar RB-60.qxd 4/11/06 2:04 PM Page 5
Fig. 3
2. Rotate the tray, until the corners of the
tray "click" into place.
ASSEMBLE YOUR TRIPOD
The tripod is the basic support for your
telescope. Adjust the height of the tripod so
that you can view comfortably.
3
ATTACH THE MOUNT TO THE TRIPOD
Fig. 2
1. Unlock the leg lock (20).
1. Slide the center
post of the mount into
the center hole on top
of the tripod.
2. Tighten the lock
knob (10) underneath
the top of the tripod
to firm feel. Notice
that the lock knob is
already attached to
the tripod.
2. Slide the leg in or out to the desired
length.
3. Tighten the leg lock to secure the leg
in place.
4. Repeat for the other two legs.
5. Next, spread the legs out evenly apart.
Inset B
ATTACH THE RED DOT VIEWFINDER
It can be difficult locating objects in the
sky using the eyepiece. The red dot
viewfinder has a red dot "bullseye" to help
you more easily locate and line up with a
celestial target.
Slide the red dot viewfinder into the
mounting bracket until it clicks into place.
Note that the red dot viewfinder has a quick
release control. To detach from the bracket,
press the bracket quick release button and
slide the bracket out.
ATTACH THE OPTICAL TUBE TO THE MOUNT
The optical tube gathers distant light which
is focused in the eyepiece.
1. Remove the two lock knobs from the
optical tube. (Fig. 3)
Fig. 4
ATTACH THE ACCESSORY TRAY
The tray (17) helps stabilize the tripod and
is also a convenient holder of eyepiece and
other Meade accessories, such as the
Barlow lens.
1. Place the accessory tray over the center
hub of the leg brace supports.
2. Slide the two bolts through the holes in
the mounting bracket.
3. Thread a lock knob onto each of the
mounting screws and tighten to a
firm feel.
Telestar RB-60.qxd 4/11/06 2:04 PM Page 6
2. Look through the red dot viewfinder. Turn
one or more of the viewfinder’s alignment
screws (3) until the red dot is precisely
over the same object as you centered in
the eyepiece.
3. Check this alignment at night on a
celestial object, such as the Moon or
a bright star, and use the viewfinder’s
alignment screws to make any
necessary refinements.
movements as you follow (or “track”) an
object as it moves in the eyepiece.
ATTACH THE DIAGONAL MIRROR
AND EYEPIECE
4
The diagonal mirror reflects the light
THE MOST IMPORTANT RULE
from the optical tube to a more
comfortable viewing position for
the eyepiece.
We have one very important rule that
you should always follow when using
your telescope:
1. Slide the diagonal mirror into the focuser
drawtube.
2. Tighten the drawtube thumbscrew to hold
the diagonal mirror securely.
3. Slide the 25mm eyepiece into diagonal
mirror.
4. Tighten the diagonal mirror thumbscrew
to hold the eyepiece securely.
Have Fun!
Have a good time when you’re observing. You
may not know everything that there is to
know about a telescope or what all the
sights in the universe are, but that’s OK. Just
point and observe at first.
TO MOVE THE TELESCOPE
Your RB-60 telescope is altazimuth
mounted. Altazimuth is just a complicated
way of saying that your telescope moves
up and down and from side to side.
Other telescopes may be mounted in
different ways.
1. Slightly loosen the vertical locking lever
(5). Loosening this lever allows you to
move the telescope up and down.
ALIGN THE RED DOT VIEWFINDER
Perform the first part of this procedure
during the daytime and the last step at night.
1. Point the telescope at an easy-to-find
land object such as the top of a telephone
pole or a distant mountain or tower. Look
through the eyepiece in the diagonal
mirror and turn the focuser knob (23)
until the image is sharply focused. Center
the object precisely in the eyepiece’s field
of view.
2. Slightly loosen the horizontal lock knob
(6). Loosening this lock allows the
telescope to be moved from side to side.
3. Once an object is found, re-tighten the
knob. You can then use the slow motion
controls to make smooth and precise
Telestar RB-60.qxd 4/11/06 2:04 PM Page 7
SUN WARNING
You will enjoy your telescope even more
as you learn more about it. But don’t be
scared off by difficult terms or
complicated procedures. Don’t panic!
Just relax and enjoy your scope.
locating with the eyepiece. Line
up the object with the viewfinders
red dot.
NEVER USE YOUR TELESCOPE
TO LOOK AT THE SUN!
5
LOOKING AT OR NEAR THE SUN WILL CAUSE
INSTANT AND IRREVERSIBLE DAMAGE TO
YOUR EYE. EYE DAMAGE IS OFTEN PAINLESS,
SO THERE IS NO WARNING TO THE OBSERVER
THAT DAMAGE HAS OCCURRED UNTIL IT IS
TOO LATE. DO NOT POINT THE TELESCOPE OR
ITS VIEWFINDER AT OR NEAR THE SUN. DO
NOT LOOK THROUGH THE TELESCOPE OR ITS
VIEWFINDER AS IT IS MOVING. CHILDREN
SHOULD ALWAYS HAVE ADULT SUPERVISION
WHILE OBSERVING.
Look through the eyepiece: Once you
have the object lined up in the viewfinder,
look through the optical tube’s eyepiece. If
you have aligned your viewfinder, you will
you see the object in your eyepiece.
You will begin to grow and learn more
about astronomy the more you observe.
Go to the library and read some books
about the stars and planets. Read about
astronomers of old. Many of them had
telescope no bigger than the one you
are using right now. Galileo, who is one
of the first astronomers to use a
telescope, discovered four of the moons
of Jupiter with a telescope about the
same size as yours (and his didn’t even
focus very well!).
Focus: Look through the eyepiece and
practice focusing on the object you
have chosen.
Try out the slow motion adjustment
controls: To move the telescope from
side to side, first unlock the azimuth lock.
Then rotate the horizontal slow motion
control wheel to move the telescope from
side to side.
Unlock the lock knobs: To move the
telescope, you will need to unlock the
horizontal lock knob (6) and vertical
locking lever(5) (just rotate to unlock or
lock; when locking, only tighten to a “firm
feel,” do not overtighten).
OBSERVING
Observe during the daytime: Try out your
telescope during the daytime at first. It is
easier to learn how it operates and how to
observe when it is light.
THE MEADE 4M COMMUNITY
Use the red dot viewfinder: If you have not
done so, align the viewfinder (2) with the
telescope’s eyepiece (1) as described earlier.
You haven’t just bought a telescope, you have embarked
on an astronomy adventure that never ends. Share the
journey with others by accepting your free membership
in the 4M community of astronomers.
Pick out an easy object to observe:
A distant mountain, a large tree, a
lighthouse or skyscraper make excellent
targets. Point the optical tube so it lines
up with your object.
Look through the viewfinder until you can
see the object. It will be easier to locate
an object using the viewfinder rather than
today.
Telestar RB-60.qxd 4/11/06 2:04 PM Page 8
Look for different features on the Moon. The
most obvious features are craters. In fact
you can see craters within craters. Some
craters have bright lines about them. These
are called rays and are the result of material
thrown out of the crater when it was struck
by a colliding object. The dark areas on the
Moon are called maria and are composed of
lava from the period when the Moon still had
volcanic activity. You can also see mountain
ranges and fault lines on the Moon.
To move the telescope up and down,
unlock the altitude lock. Then rotate
in your telescope: Venus, Mars, Jupiter
and Saturn.
6
the altitude control wheel to move the
telescope up or down.
Nine planets (maybe more!) travel in a fairly
circular pattern around our Sun. Any system
of planets orbiting one or more stars is
called a solar system. Our Sun, by the way,
is a single, yellow dwarf star. It is average as
far as stars go and is a middle aged star.
Observe the Moon: When you feel
comfortable with the viewfinder, the
eyepieces, the locks and the adjustment
controls, you will be ready to try out the
telescope at night. The Moon is the best
object to observe the first time you go
out at night. Pick a night when the Moon
is a crescent. No shadows are seen
during a full Moon, making it appear flat
and uninteresting.
Beyond the planets are clouds of comets, icy
planetoids and other debris left over from
the birth of our sun. Recently astronomers
have found large objects in this area and
they may increase the number of planets in
our solar system.
Use a neutral density filter (often called a
“moon filter”) when observing the Moon.
Neutral density filters are available from
Meade as an optional accessory and
enhance contrast to improve your
observation of lunar features.
The four planets closest to the Sun are rocky
and are called the inner planets. Mercury,
Venus, Earth and Mars comprise the inner
planets. Venus and Mars can be easily seen
in your telescope.
TOO MUCH POWER?
Can you ever have too much power? If the type of
power you’re referring to is eyepiece magnification,
yes you can! The most common mistake of the
beginning observer is to “overpower” a telescope
by using high magnifications which the telescope’s
aperture and atmospheric conditions cannot
reasonably support. Keep in mind that a smaller,
but bright and well-resolved image is far superior
to one that is larger, but dim and poorly resolved.
Powers above 400x should be employed only under
the steadiest atmospheric conditions.
Spend several nights observing the Moon.
Some nights, the Moon is so bright that it
makes other objects in the sky difficult to
see. These are nights that are excellent for
lunar observation.
Venus is seen before dawn or after sunset,
because it is close to the Sun. You can
observe Venus going through crescent
phases. But you cannot see any surface
detail on Venus because it has a very thick
atmosphere of gas.
Observe the Solar System: After observing
the Moon, you are ready to step up to the
next level of observation, the planets. There
are four planets that you can easily observe
Telestar RB-60.qxd 4/11/06 2:04 PM Page 9
Fig. 5
When Mars is close to the Earth, you can see
some details on Mars, and sometimes even
Mars’ polar caps. But quite often, Mars is
further away and just appears as a red dot
with some dark lines crisscrossing it.
Probably the most memorable sight
you will see in your telescope is
Saturn. Although you may not see
many features on the surface of
Saturn, its ring structure will steal
7
your breath away. You will probably be able
to see a black opening in the rings, known
as the Cassini band.
Jupiter, Saturn, Uranus, Neptune and Pluto
comprise the outer planets. These planets,
except for Pluto, are made mostly of gases
and are sometimes called gas giants. If they
had grown much bigger, they may have
become stars. Pluto is made mostly of ice.
Saturn is not the only planet that has rings,
but it is the only set of rings that can be
seen with a small telescope. Jupiter’s rings
cannot be seen from Earth at all—the
Voyager spacecraft discovered the ring after
it passed Jupiter and looked back at it. It
on the face of Jupiter, see one moon eclipse
another or even see a moon emerge from
behind Jupiter’s giant disk. Drawing the
positions of the moons each night is an
excellent exercise for novice astronomers.
Jupiter is quite interesting to observe. You
can see bands across the face of Jupiter. The
more time you spend observing these bands,
the more detail you will be able to see.
One of the most fascinating sights of Jupiter
are its moons. The four largest moons are
called the Galilean moons, after the
Any small telescope can see the four
Galilean moons of Jupiter (Fig. 5), plus a few
others, but how many moons does Jupiter
actually have? No one knows for sure! Nor
are we sure how many Saturn has either. At
last count, Jupiter had over 60 moons, and
held a small lead over Saturn. Most of these
moons are very small and can only be seen
with very large telescopes.
astronomer Galileo, who observed them for
the first time. If you’ve never watched the
Galilean moons in your telescope before,
you’re missing a real treat! Each night, the
moons appear in different positions around
the Jovian sky. This is sometimes called the
Galilean dance. On any given night, you
might be able to see the shadow of a moon
Telestar RB-60.qxd 4/11/06 2:04 PM Page 10
turns out, only with the sunlight
interesting. But look again. There is much
information that is revealed in stars.
You may be able to see the Andromeda
galaxy and several others in your telescope.
They will appear as small, fuzzy clouds. Only
very large telescope will reveal spiral or
elliptical details.
shining through them, can the rings
8
be seen. Uranus and Neptune also
have faint rings.
The first thing you will notice is that not all
stars are the same colors. See if you can find
blue, orange, yellow, white and red stars.
The color of stars sometimes can tell you
about the age of a star and the temperature
that they burn at.
Optional color filters help bring out detail
and contrast of the planets. Meade offers a
line of inexpensive color filters.
You will also be able to see some nebulas
with your scope. Nebula means cloud. Most
nebulas are clouds of gas. The two easiest to
see in the Northern Hemisphere are the
Orion nebula during the winter and the
Triffid nebula during the summer. These are
large clouds of gas in which new stars are
being born. Some nebulas are the remains
of stars exploding. These explosions are
called supernovas.
What’s Next? Beyond the Solar System:
Once you have observed our own system of
planets, it’s time to really travel far from
home and look at stars and other objects.
Other stars to look for are multiple stars.
Very often, you can find double (or binary)
stars, stars that are very close together.
These stars orbit each other. What do
you notice about these stars? Are they
different colors? Does one seem brighter
than the other?
You can observe thousands of stars with
your telescope. At first, you may think stars
are just pinpoints of light and aren’t very
When you become an advanced observer you
can look for other types of objects such as
asteroids, planetary nebula and globular
clusters. And if you’re lucky, every so often a
bright comet appears in the sky, presenting
an unforgettable sight.
Almost all the stars you can see in the sky
are part of our galaxy. A galaxy is a large
grouping of stars, containing millions or
even billions of stars. Some galaxies form a
spiral (like our galaxy, the Milky Way) and
other galaxies look more like a large football
and are called elliptical galaxies. There are
many galaxies that are irregularly shaped
and are thought to have been pulled apart
because they passed too close to—or even
through—a larger galaxy.
The more you learn about objects in the
sky, the more you will learn to appreciate
the sights you see in your telescope. Start
a notebook and write down the observations
you make each night. Note the time and
the date.
Telestar RB-60.qxd 4/11/06 2:04 PM Page 11
Use a compass to make a circle, or trace
around the lid of a jar. Draw what you see in
your eyepiece inside the circle. The best
exercise for drawing is to observe the moons
of Jupiter every night or so. Try to make
Jupiter and the moons approximately the
same size as they look in your eyepiece. You
will see that the moons are in a different
position every night. As you get better at
drawing, try more challenging sights, like a
crater system on the moon or even a nebula.
Fig. 6
Barlow lens: You can also change
magnification by using your Barlow.
Remove the eyepiece from the
diagonal mirror and slide in the
Barlow. And then place the eyepiece
into the Barlow. Tighten the thumbscrews to
secure the Barlow lens and the eyepiece in
place. The Barlow lens included with your
telescope doubles the power of your
telescope. (Fig. 6).
eyepiece
barlow
9
diagonal
mirror
Meade offers a complete line of eyepieces
for your telescope. Most astronomers have
four or five low-power and high power
eyepieces to view different objects and to
cope with different viewing conditions.
Go your library or check out the internet for
more information about astronomy. Learn
about the basics: light years, orbits, star
colors, how stars and planets are formed,
red shift, the big bang, what are the different
kinds of nebula, what are comets, asteroids
and meteors and what is a black hole. The
more you learn about astronomy, the more
fun, and the more rewarding your telescope
will become.
viewing conditions. Use the high-power 9mm
eyepiece to view details when observing the
Moon and planets. If the image become
fuzzy, switch back down to a lower power.
Changing eyepieces changes the power or
magnification of your telescope.
Objects move in the eyepiece: If you are
observing an astronomical object (the Moon,
a planet, star, etc.) you will notice that the
object will begin to move slowly through the
telescopic field of view. This movement is
caused by the rotation of the Earth and
makes an object move through the tele-
scope’s field of view. To keep astronomical
objects centered in the field, simply move
the telescope on one or both of its axes—
vertically and/or horizontally as needed—try
By the way, you might have noticed
something strange when you looked through
your eyepiece. Although the image is right-
side up, it is reversed. That means reading
words can be a problem. But it has no affect
on astronomical objects. If you wish to have
a fully corrected image, check out Meade’s
optional Erecting Prism in the Optional
Accessory section.
SOME OBSERVING TIPS
Eyepieces: Always begin your observations
using the 25mm low-power eyepiece. The
25mm eyepiece delivers a bright, wide field
of view and is the best to use for most
Telestar RB-60.qxd 4/11/06 2:04 PM Page 12
using the telescopes coarse and fine
adjustment controls. At higher
lack sharpness—the same object, when
observed higher in the sky, will appear
sharper and have greater contrast. Try
reducing power (change your eyepiece) if
your image is fuzzy or shimmers. Keep in
mind that a bright, clear, but smaller image
is more interesting than a larger, dimmer,
fuzzy one. Using too high a power eyepiece is
one of the most common mistakes made by
new astronomers.
cause the image to move. Avoid observing
sites where vibrations cause image
movement (for example, near railroad
tracks). Viewing from the upper floors of a
building may also cause image movement.
10
powers, astronomical objects will
seem to move through the field of
view of the eyepiece more rapidly.
Place the object to be viewed at the edge of
the field and, without touching the telescope,
watch it drift through the field to the other
side before repositioning the telescope
so that the object to be viewed is again
placed at the edge of the field, ready to be
further observed.
Let your eyes “dark-adapt”: Allow five or
ten minutes for your eyes to become “dark
adapted” before observing. Use a red-
filtered flashlight to protect your night vision
when reading star maps, or inspecting the
telescope. Do not use use a regular flash-
light or turn on other lights when observing
with a group of other astronomers. You can
make your own red filtered flashlight by
taping red cellophane over a flashlight lens.
Dress Warm: Even on summer nights, the
air can feel cool or cold as the night wears
on. It is important to dress warm or to have
a sweater, jacket, gloves, etc., nearby.
Vibrations: Avoid touching the eyepiece
while observing through the telescope.
Vibrations resulting from such contact will
Know your observing site: If possible,
know the location where you will be
observing. Pay attention to holes in the
ground and other obstacles. Is it a location
where wild animals, such as skunks, snakes,
etc., may appear? Are there viewing
obstructions such as tall trees, street lights,
headlights and so forth? The best locations
are dark locations, the darker the better.
Deep space objects are easiest to see under
dark skies. But it is still possible to observe
even in a city.
Viewing through windows: Avoid setting up
the telescope inside a room and observing
through an opened or closed window pane.
Images may appear blurred or distorted due
to temperature differences between inside
and outside air. Also, it is a good idea to
allow your telescope to reach the ambient
(surrounding) outside temperature before
starting an observing session.
STAR CHARTS
Star charts and planispheres are useful for a variety of
reasons. In particular, they are a great aid in planning a
night of celestial viewing.
A wide variety of star charts are available in books, in
magazines, on the internet and on CD Roms. Meade
offers Autostar Suite™ software. Contact your local
Meade dealer or Meade’s Customer Service department
for more information.
Astronomy and Sky and Telescope magazines print star
charts each month for up-to-the-minute maps of the
heavens.
When to observe: Planets and other
objects viewed low on the horizon often
Telestar RB-60.qxd 4/11/06 2:04 PM Page 13
always described by how large their
objective lens is. Your telescope is 60mm
or 2.4 inches. Other telescopes are 90mm,
8 inches, 16 inches, or even 3 feet in
diameter. The Hubble Telescope’s objective
lens has a diameter of 2.4 meters (that’s
7.8 feet across!).
Surf the Web and visit your local library:
The internet contains a huge amount of
astronomical information, both for children
and adults. Check out astronomy books from
your library. Look for star charts—these are
available on a monthly basis in Astronomy
and Sky and Telescope magazines.
reducers to make slow exposure
telescopes have faster focal ratios.
11
Altaz mounting simply means your
telescope moves up and down
(altitude or “alt”), and side to side, (azimuth
or “az”). Other mounting configurations are
available for other telescopes, such as
equatorial mounting.
HAVE A GOOD TIME,
ASTRONOMY IS FUN!
ASTRONOMY RESOURCES
USE THE SPECIFICATIONS TO CALCULATE
THE MAGNIFICATION OF YOUR EYEPIECE
•
•
The Meade 4M Community
6001 Oak Canyon, Irvine, CA 92618
Astronomical League
SPECIFICATIONS
The power of a telescope is how much it
magnifies objects. Your 25mm eyepiece
magnifies an object 28 times. Your 9mm
eyepiece magnifies objects 78 times.
Executive Secretary
Optical tube focal length . . . . . . . . . 700mm
Objective lens diameter . . . . . . 60mm (2.4")
Focal ratio. . . . . . . . . . . . . . . . . . . . . . . f/11.6
Mounting type . . . . . . . . . . . . . . . Altazimuth
5675 Real del Norte, Las Cruces, NM 88012
The Astronomical Society of the Pacific
390 Ashton Avenue, San Francisco, CA 94112
The Planetary Society
65 North Catalina Avenue, Pasadena, CA 91106
International Dark-Sky Association, Inc.
3225 N. First Avenue, Tucson, AZ 85719-2103
•
•
•
But if you obtain other eyepieces, you can
calculate how much magnification they have
with your telescope. Just divide the focal
length of the telescope by the focal length of
the eyepiece.
What do the specifications mean?
Optical tube focal length is simply a
measurement of the length of the optical
tube. In other words, this is the distance
light travels in the tele-scope before being
brought to focus in you eyepiece. Your tube is
700mm long.
The focal ratio helps determine how fast the
photographic speed of a telescope is. The
lower the focal ratio number, the faster the
exposure. f/5 is faster than f/10. The faster
the ratio, the faster exposure time is needed
when a camera is hooked up to the tele-
scope. Your telescope has slower focal ratio
at f/11.6. Sometimes, astronomers use focal
Focal Length of the Telescope
÷
Focal Length of the Eyepiece
=
Objective lens diameter is how big the
lens is on your scope. Telescopes are
Magnification
Telestar RB-60.qxd 4/11/06 2:04 PM Page 14
Look at the specifications. You will
see that the focal length of your
magnification is when you use a Barlow,
multiply your eyepiece’s magnification
by two.
• Avoid cleaning the telescope’s lenses. A
little dust on the front surface of the
telescope’s correcting lens will not cause
loss of image quality.
12
scope is 700mm. Let’s say that you
have obtained a 13mm eyepiece. You
can tell that what the focal length of
your eyepiece is as it is always printed on
the side of an eyepiece. Divide: 700 ÷ 13,
which equals 53.8. Round this off to the
nearest whole number and your new
eyepiece magnifies objects 54 times.
Eyepiece’s magnification x 2
=
• When absolutely necessary, dust on the
front lens should be removed with very
gentle strokes of a camel hair brush or
blown off with an ear syringe (available at
most pharmacies).
Magnification with a 2X Barlow lens
Your 25mm low-power eyepiece magnifies
an object 28 times. Multiply 28 by 2 and you
get 56 times magnification with your Barlow.
• Fingerprints and organic materials on the
front lens may be removed with a solution
of 3 parts distilled water to 1 part
If you use your Barlow lens with one of your
eyepieces, it doubles the magnification of
your eyepiece. Other types of Barlows can
triple or further increase the power of an
eyepiece. To find out how much your
It’s worth repeating: Keep in mind that a
bright, clear, but smaller image is more
interesting than a larger, dimmer, fuzzy one.
Using too high a power eyepiece is one of
the most common mistakes made by new
astronomers. So don’t think that higher
magnification is necessarily better—quite
often the best view is with lower
isopropyl alcohol. You may also add 1 drop
of biodegradable dishwashing soap per
pint of solution. Use soft, white facial
tissues and make short, gentle strokes.
Change tissues often.
CAUTION: Do not use scented or lotioned
tissues or damage could result to the optics.
DO NOT use a commercial photographic
lens cleaner.
magnification value!
TAKING CARE OF YOUR TELESCOPE
Your telescope is a precision optical
instrument designed for a lifetime of
rewarding viewing. It will rarely, if ever,
require factory servicing or maintenance.
Follow these guidelines to keep your
telescope in the best condition:
OPTIONAL ACCESSORIES
#928 45° Erecting Prism (1.25 O.D.):
Correctly orients the telescopic image
during terrestrial observing and yields an
image position at a 45° angle to the main
Telestar RB-60.qxd 4/11/06 2:04 PM Page 15
telescope tube, resulting in a more comfor-
table observing position in most cases.
13
Additional Eyepieces (1.25" barrel
diameter): For higher or lower
magnifications with the telescopes that
accommodate 1.25" eyepieces, Meade Series
4000 Super Plössl eyepieces, available in a
wide variety of sizes, provide a high level of
image resolution and color correction at an
economical price. Contact your Meade
Dealer or see the Meade catalog for more
information. Visit us on the web at
JOIN AN ASTRONOMY CLUB, ATTEND A STAR PARTY
One of the best ways to increase your knowledge of
astronomy is to join an astronomy club. Check your
local newspaper, school, library, or telescope dealer/
store to find out if there’s a club in your area.
Many groups also hold regularly scheduled Star Parties
at which you can check out and observe with many
different telescopes and other pieces of astronomical
equipment. Magazines such as Sky and Telescope and
Astronomy print schedules for many popular Star
Parties around the United States and Canada.
Telestar RB-60.qxd 4/11/06 2:04 PM Page 16
Meade, freight-prepaid, with proof of
purchase. This warranty applies to the
original purchaser only and is non-
transferable. Meade products purchased
outside North America are not included in
this warranty, but are covered under
separate warranties issued by Meade
international distributors.
limited to a term of one year from the date
of original retail purchase.
MEADE CONSUMER SOLUTIONS
If you have a question concerning
your telescope, call Meade
Instruments Consumer Solutions
Department at (800) 626-3233.
14
This warranty gives you specific rights. You
may have other rights which vary from state
to state.
Consumer Solutions Departmant hours are
8:00AM to 5:00PM, Pacific Time, Monday
through Friday. Write or call the Meade
Consumer Solutions Department first,
before returning the telescope to the factory,
giving full particulars as to the nature of the
problem, as well as your name, address, and
daytime telephone number. The great
majority of servicing issues can be resolved
by telephone, avoiding return of the
telescope to the factory.
Meade reserves the right to change product
specifications or to discontinue products
without notice.
RGA Number Required: Prior to the return
of any product or part, a Return Goods
Authorization (RGA) number must be
obtained from Meade by writing, or by
calling (800) 626-3233. Each returned part or
product must include a written statement
detailing the nature of the claimed defect, as
well as the owner’s name, address, and
phone number.
This warranty supersedes all previous
Meade product warranties.
SURF THE WEB
MEADE LIMITED WARRANTY
•
•
•
•
•
•
The Meade 4M Community:
This warranty is not valid in cases where the
product has been abused or mishandled,
where unauthorized repairs have been
attempted or performed, or where
depreciation of the product is due to normal
wear-and-tear. Meade specifically disclaims
special, indirect, or consequential damages
or lost profit which may result from a breach
of this warranty. Any implied warranties
which cannot be disclaimed are hereby
Every Meade telescope and telescope
accessory is warranted by Meade
Instruments Corporation (“Meade”) to be
free of defects in materials and
workmanship for a period of ONE YEAR from
the date of original purchase in the U.S.A.
Meade will repair or replace a product, or
part thereof, found by Meade to be defective,
provided the defective part is returned to
Sky & Telescope:
Astronomy:
Astronomy Picture of the Day:
Photographic Atlas of the Moon:
Hubble Space Telescope Public Pictures:
©2006 MEADE INSTRUMENTS CORPORATION
Telestar RB-60.qxd 4/11/06 2:04 PM Page 17
OBSERVATION LOG
OBSERVER:
OBJECT NAME:
DATE & TIME OBSERVED:
CONSTELLATION:
EYEPIECE SIZE:
SEEING CONDITIONS:
NOTES:
EXCELLENT
GOOD
POOR
DRAWING OF IMAGE
(SAVE ORIGINAL - BE SURE TO MAKE COPIES)
Telestar RB-60.qxd 4/11/06 2:04 PM Page 18
OBSERVATION LOG
OBSERVER:
OBJECT NAME:
DATE & TIME OBSERVED:
CONSTELLATION:
EYEPIECE SIZE:
SEEING CONDITIONS:
NOTES:
EXCELLENT
GOOD
POOR
DRAWING OF IMAGE
Telestar RB-60.qxd 4/11/06 2:04 PM Page 19
Telestar RB-60.qxd 4/11/06 2:04 PM Page 20
Meade Instruments Corporation
1-800
6001 Oak Canyon, Irvine, California
92618
|